(No Ratings Yet)
Loading...To obtain the ILOM serial number Type the following command:
|
1 |
show /SYS product_serial_number |
The following is an example of the results of this command
|
1 2 3 |
/SYS Properties: product_serial_number = 0723BBC006 |
This serial number should always match the serial number returned by service tags on the host; it should also match the serial number on the label located on the front of the […]
(No Ratings Yet)Loading...Clearing a Hardware Fault On A SUN / Oracle Hardware First, launch the Fault Management shell from the SP or CMM CLI. Type one of the following:
|
1 2 |
start /SP/faultmgmt/shell start /CMM/faultmgmt/shell |
Sub-command Syntax Examples
|
1 2 3 4 5 6 7 |
fmadm repaired /SYS/MB/FM0 fmadm repaired /SYS/PS1 fmadm replaced /SYS/MB/FM0 fmadm replaced /SYS/PS1 # OR somthing like the below fmadm repaired /SYS/RCSA/PCIE2/CAR |
Oracle Reference http://docs.oracle.com/cd/E24707_01/html/E24528/z40013e61440963.html
(No Ratings Yet)Loading...https://wikis.oracle.com/display/SystemsComm/Cross+Platform+IO+Support
(No Ratings Yet)Loading...Web Procedure – Enable or Disable Locate LED In the web interface, click System Monitoring –> Indicators. In the Actions list box, click Name: Locate. To illuminate the Locator LED, select the radio button adjacent to /SYS/LOCATE, and then click Set LED to Fast Blink. To disable the Locator LED, select the radio button adjacent […]
(No Ratings Yet)Loading...Recovering TX000 ALOM Passwords Procedure as below for reseting the T2000 ALOM password due to no scadm command available for the sun4v architecture in Solaris 10. Recovering TX000 ALOM Passwords For security reasons, this procedure is available only while accessing the system directly through the serial port. The procedure resets all ALOM NVRAM settings. To […]
(1 votes, average: 5.00 out of 5)Loading...Contents 1 Oracle VM for SPARC configuration for T5-2 1.1 Primary domain config 1.2 Primary network config 1.2.1 T5-2 ldom config 1.2.2 Configure CD-Rom for OS install 1.2.3 Configure DCX/FC switch zoning for SAN boot Disk 1.3 Configure PCI bus / Ethernet & FC slots 1.4 Save the ldom config / configure ldom auto save […]
(No Ratings Yet)Loading...Contents 1 NetBackup Oracle VM for SPARC configuration 1.1 Primary domain config 1.2 Primary network config 1.2.1 BKM ldom config 1.2.2 Configure CD-Rom for OS install 1.2.3 Configure DCX/FC switch zoning for SAN boot Disk 1.3 Configure PCI bus / Ethernet & FC slots 1.3.1 Remove PCI bus from the primary domain 1.3.1.1 Turn on […]
(No Ratings Yet)Loading...Sun Fire Mx00 initial configuration login with admin, if admin doesn’t work use default which will wait till the key is turned.
|
1 |
login: admin |
Cerate user jsmith and privileges
|
1 2 3 4 |
XSCF> adduser -u 921 jsmith XSCF> password jsmith XSCF> setprivileges jsmith platadm fieldeng useradm mode auditadm XSCF> exit |
login as jsmith Get all hardware configs
|
1 2 3 4 5 6 7 8 9 |
XSCF> showhardconf SPARC Enterprise M5000; + Serial:BEF1016D82; Operator_Panel_Switch:Locked; + Power_Supply_System:Single; SCF-ID:XSCF#0; + System_Power:On; System_Phase:Cabinet Power On; Domain#0 Domain_Status:Running; snip [...] console -d 0 |
M5000 IP Setup Example Configuration
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 |
#configure the IP for XSCF-LAN#0 on XSCF Unit 1 XSCF> setnetwork xscf#1-lan#0 -m <netmask> <IP> XSCF> setnetwork -c up <interface> XSCF> shownetwork XSCF> setroute -c add -n <IP> -g <IP> <interface> #After configuring the interface, you must apply then reboot the xscf. XSCF> applynetwork XSCF> rebootxscf # After reboot, verify network settings XSCF> shownetwork -a #set hostname and dns server for xscf XSCF> sethostname <xscf#0|xscf#1> <hostname> XSCF> sethostname -d <domainname> XSCF> showhostname -a XSCF> setnameserver <IP> #add the NTP server XSCF> setntp -c add <IP> XSCF> rebootxscf #enable http, email and ssh services XSCF> sethttps -c enable XSCF> setsmtp XSCF> setssh -c enable |
Example configuration
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 |
XSCF> adduser admin XSCF> password admin New XSCF password: BAD PASSWORD: it does not contain enough DIFFERENT characters Retype new XSCF password: XSCF> setprivileges admin useradm platadm platop fieldeng XSCF> adduser admin2 password admin2 XSCF> password admin2 New XSCF password: Retype new XSCF password: setprivileges admin2 useradm platadm platop fieldeng XSCF> setprivileges admin2 useradm platadm platop fieldeng XSCF> setnetwork xscf#0-lan#0 -m 255.255.248.0 10.20.105.12 XSCF> setnetwork -c up xscf#0-lan#0 XSCF> setroute -c add -n 0.0.0.0 -g 10.20.104.1 xscf#0-lan#0 XSCF> sethostname xscf#0 informix2-xscf XSCF> sethostname -d domain.com XSCF> applynetwork The following network settings will be applied: xscf#0 hostname :informix2-xscf DNS domain name :domain.com interface :xscf#0-lan#0 status :up IP address :10.20.105.12 netmask :255.255.248.0 route :-n 0.0.0.0 -m 0.0.0.0 -g 10.20.104.1 interface :xscf#0-lan#1 status :down IP address : netmask : route : Continue? [y|n] :y Please reset the XSCF by rebootxscf to apply the network settings. Please confirm that the settings have been applied by executing showhostname, shownetwork, showroute and shownameserver after rebooting the XSCF. XSCF> XSCF> rebootxscf The XSCF will be reset. Continue? [y|n] :y XSCF> execute J00shutdown_start -- complete execute K000end -- complete execute S10ioxoff -- complete [...] XSCF> shownetwork -a xscf#0-lan#0 Link encap:Ethernet HWaddr 00:21:28:B0:64:72 inet addr:10.20.105.12 Bcast:10.20.111.255 Mask:255.255.248.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Base address:0xe000 xscf#0-lan#1 Link encap:Ethernet HWaddr 00:21:28:B0:64:73 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Base address:0xc000 XSCF> setnameserver 10.20.8.60 XSCF> setntp -c add 10.20.18.141 XSCF> setssh -c enable Continue? [y|n] :y Please reset the XSCF by rebootxscf to apply the ssh settings. XSCF> setdscp DSCP network [0.0.0.0 ] > 10.1.1.0 DSCP netmask [255.0.0.0 ] > 255.255.255.0 XSCF address [10.1.1.1 ] > 10.20.105.12 ERROR: Address out of range. Try again. XSCF address [10.1.1.1 ] > 10.1.1.10 Domain #00 address [10.1.1.11 ] > Domain #01 address [10.1.1.12 ] > Domain #02 address [10.1.1.13 ] > Domain #03 address [10.1.1.14 ] > Commit these changes to the database? [y|n] : y |
configuration example The simplest forum is to run
|
1 2 3 4 |
XSCF> setupplatform -p user # Then XSCF> setupplatform -p network |
[…]